In a few cases, the tank may be a predecessor model. These older tanks do not have the flexible hose inside. The lid of the tank must be closed so that the hose rests on the underside of the tank and does not end in an air pocket on the top of the tank. If the tank leaks, check that the cap has been properly and tightly closed.
The software probably stopped working. Unplug the unit, wait one minute and reconnect. Depending on your firmware version, you can continue with the previous cleaning cycle.
If this is not the case, go through the steps "E-cleaning 7" to "E-cleaning 12" page 28 of your operating instructions manually and without regard to the instructions on the display. If the process stops suddenly after you touch the screen to check the remaining time, you probably touched the stop button.
Note that the screen is still active and reacts when it is dark. Therefore, do not touch the display near the stop button. In a few cases, it may be that the tank is a previous model. The lid of the tank must be closed so that the hose rests on the underside of the tank and does not end in air pockets at the top of the tank.
If the tank leaks, check if the lid is properly and firmly closed. Presumably the software has hung up. Disconnect the device from the circuit, wait a minute and reconnect it. Depending on your firmware version, you can continue the previous cleaning cycle. If this is not the case, go through the steps "E-cleaning 7" to "E-cleaning 12" page 28 of your operating manual manually and without regard to the instructions of the display.
If the process stops suddenly after touching the remaining time screen, you may have touched the Stop button. Please note that the screen is active an reacts even when it is dark. This can happen if the faucet has been turned on within the first 30 minutes during the cleaning process.
Please touch the screen when the cleaning cycle has been in progress for more than 30 minutes. If the screen is currently active, wait until it enters standby mode before touching it. Never seal the flexible hose under any circumstances. The only hose that can be closed during E-cleaning is the secondary hose. First, thoroughly clean the thread and tank lid. Also check if the contacts inside the compartment are free or stuck.
It is possible that salt crystals have settled behind the pins, which prevents the machine from recognizing the tank. Use a damp cloth or a damp cotton swab to gently clean the pins and possibly loosen any salt crystals stuck behind them.
You can also use a thin, smooth object such as the end of a ballpoint pen to gently push in the pins and gently dislodge the salt crystals behind them. But be careful not to push the pins too far, otherwise they might disappear in the machine.
Then firmly press the tank into the compartment provided and place the cover back on the machine. Check the "pH setting" under "Settings" and increase if necessary. Also lower the pressure of the water jet on your faucet to give the necessary time to the electrolysis process in the machine.
If you're using an older generation of K8 filters, your filter may lack the protective sticker that covers the chip.
If this filter gets wet, it can happen that the machine does not recognize it. Try to dry the chip with a hair dryer and avoid further contact with water. If you have access to another K8, check your filter on the other device. If it does not recognize your filter as well, the filter chip is damaged. If the other machine recognizes your filter as original, please contact our service department.
Service enagiceu. On page 24 of your operating instructions, please read under what circumstances the machine requests a filter change. If none of these conditions apply to your case, please send a picture of the display bars under "Filter Control" on our display to our service department service enagiceu. In addition, inform our service team as precisely as possible about the time of the last filter change and the regularity with which you clean the machine. Only with this information, we can help you properly.
Please understand that we cannot replace filters that have been in use for several months before the problem occurred, as we cannot track the amount of water used in this case. LeveLuk has an automatic cleaning system. The amount of minerals in the feedwater, such as Ca and Mg, can vary widely, and mineral1 clusters inevitably adhere to the electrode plates.
The amount of minerals adhering to the electrolytic cell will vary depending on the amount of minerals in the tap water. The LeveLuk automatic cleaning mechanism activates for 20 seconds when continuous electrolysis reaches 15 minutes.
If you use LeveLuk in areas where the water is high in minerals, change the "beauty water" setting 2nd from the bottom and turn the faucet lightly to allow the water to run smoothly.
This reverses the electrical current and removes the crystals in the electrolysis cell after minutes. If you change the setting to "beauty water" once a day for 30 seconds, you can also clean the electrolytic cell. The cleaning function is required to maximize the life of the electrolytic cell.
All other substances cannot be listed here, as the effectiveness of the filter depends on its abundance in incoming water. Note, however, that Enagic does not produce filters that can make non-potable water drinkable. Our filters and prefilters improve the overall water quality in terms of taste, odor, sediment content, hardness and removal of certain substances, and prepare the water for the electrolysis process, which is the main function of our machines.
If you do not use the machine for an extended period of time, you should first empty it completely and unplug it. After a prolonged period of non-use, an e-cleaning should always be carried out first.
It is also advisable to store the high-grade filter in the refrigerator or in a similarly cool place during this time in order to prevent mold growth. If the filter has been used before, it should not be stored for more than one month. Desalinated water does not need to be pretreated before it passes through the machine. However, other problems might arise:. If there is no water running through them, all machines automatically fall into standby mode. They are only active when the sensor registers running water.
If the gray hose acidic water is above the water outlet inside the machine, the separation of the water is partly reversed and both water types mix again, causing the mineral ions to react with mineral oxides. Kangen water is expelled by the water pressure of the faucet, whereas the acidic water is mainly due to gravity.
So, there is not much pressure on the gray hose when it is lifted over the machine, which in part leads to a reversal of the electrolysis.. If the outlet hose is bent or the stand is positioned higher than the bottom tip of the flexible pipe, no acidic water can be produced.
In this case, do not pull down the stand, but prepare a separate hose to catch the water in the container. Make it a daily habit to check the water with the pH test solution and hydrogen bubbles. There is a rectangular switch under the black cover on the left front of the device. Be sure to press this button a beep should sound when setting up the LeveLuk for the first time or replacing the filter.
This allows the correct display of all information stored on the LeveLuk microcomputer liquid crystal display. This reset button must be pressed to display information on the LCD screen. It notifies the user if there is too much or too little water, triggers an alarm if hot water is accidentally leaked and instructs you to monitor the flow of water.
Proper use of the reset switch on the LeveLuk ensures that safe and healthy water is supplied. LeveLuk is designed so that the flexible tube attached above is connected to the negative electrolysis cell, while the gray tube attached to the base of the LeveLuk is connected to the positive electrolysis cell. This is the only time the water is drained at the opposite ends. Since the acidic mode reverses the polarity, the calcium crystals attached to the negative pole break off and can be used as a manual cleaning mode.
Traditionally, strong acidic water could only be produced with large equipment for institutional use at that time, strongly acidic water was referred to as acidified water. We felt that it would be very useful for people's hygiene if they were able to produce and use highly acidic water in their homes.
The electrode plate in LeveLuk's electrolysis cell is thicker and larger than the products of other companies. The device is designed in this way to increase the electrolysis capacity and durability.
Another important reason is to ensure the production of maximum amounts of water. The electrode plates are made of the highest quality titanium coated with platinum. It is needless to say that due to this material selection, the electrode plates are completely rust-free. The electrolytic cell is for a water generator what the motor generator is for a car. We can recommend our products with the best of confidence as we only use the best materials. The automatic cleaning mechanism ensures that the electrolysis cell is always clean and should last 15 years.
The beauty water mode is the only one where you want to run acidic water out of the flexible pipe. In addition, using the upper flexible tube makes it easier to use the device, especially if you wash your face or fill water in a plastic bottle. Before using this water, you must remove the deposits2 mineral clusters adhering to the electrode plate1 by reversing the tension3. This is necessary to produce perfect acidic water.
If you remove the equilibrium and run acidic water through the flexible tubes, even if you do not want to use acidic water, you can keep the electrode plate clean and increase its life.
It is made of titanium and is platinum plated, so it has excellent electrolysis capacity and long life. These clusters are called scales and are not harmful even when consumed. If mineral clusters are attached to the electrode plate, you must invert the plus and minus of the current to remove the clusters. As a result, the device is always set to a cleaning function, similar to the setting "Beauty Water". The electrolysis of water requires high quality electrolysis plates.
Size, thickness and number of plates are crucial for maintaining durability. The "double cross-line" method1 used by other companies takes into account the overall durability of the devices. These devices, in turn, use two small electrolysis cells to provide a rest time, but limit the volume of water that can be produced at once. LeveLuk, on the other hand, has five or seven electrolysis plates, which is the largest number in the industry.
Every function, e. As the power supply according to the switching of the pH adjustment and the generation of strongly acidic water in the same electrolytic cell is carefully monitored by the microcomputer. It ensures that the device can be used safely over a long period of time. We recommend that you produce "beauty water" once a day for at least three minutes to improve the life of your device.
An electrolysis system where the unit is equipped with two small electrolysis cells to increase shelf life by changing cells with each water flow. LeveLuk is equipped with an automatic water drainage system that prevents the contamination and proliferation of germs in the residual water.
The automatic water drainage system is activated as soon as the water stops. It takes about 30 seconds for all the water in the electrolytic cell, the water treatment cartridge and all channels to drain through the hose gray. Please note that if the water level drops and the spout is positioned higher than the bottom of the unit for any reason accumulation of acidic water in the tank due to its length makes the hose hang from a rack , the automatic water drainage system may be activated lead that no residual water is drained off.
Leaving water can cause taste and odor problems. Make sure the outlet hose is lower than the appliance before turning off the tap. First, the following things have to be considered: 1. How old is the filter in your machine? How often do you clean the machine with citric acid powder? Please have the answers to these questions ready when you contact our service department. Unrefined water contains minerals1.
LeveLuk is designed to handle a standard amount of minerals. When the amount of minerals or free carbon dioxide2 is greater than usual, the minerals sometimes react with the antibacterial effect3 of the water supply hose and smell it. We have prepared a water supply hose such cases. If you are running water through the unit for the first time, please put it on purified water and let it run for two to three minutes longer than usual.
During ionization, positive mineral ions accumulate in the Kangen water. These react with the oxygen in the air, resulting in a thin layer of deposit on water glasses or other vessels.
The EPA manually manages the amount of Barium in public water in order to keep it below the recommended level. Cadmium is another metal that finds its way into pipes through industrial waste or fertilizer contamination. Another cause of this fish smell is the combination of chlorine and ammonia which together create a compound called Chloramine. This is often used to disinfect public water sources and can sometimes produce an unpleasant aroma in your water.
Lakes and reservoirs often see an increase in algae blooming on the surface of the water when there is plenty of warmth and direct sunlight. Although water treatment plants rid the water of the algae, the particles that cause the fishy smell can sometimes be detected by people who are overly sensitive to musty or mildew like smells. Because the smell is commonly caused by organic material in your pipes or well, there is little you can do yourself to fix the issue. Noodles boiled with ionized microcluster alkaline water become tenderer and more elastic.
Ingredients in soup materials are better separated out in ionized microcluster alkaline water which makes food more nutritious and better tasting. Taking medicine with ionized microcluster alkaline water enables elements in medicine to be better extracted and carried with water though out body.
Ionized microcluster alkaline water can be used for making beverages such as tea, coffee, wine and etc. Washing food with ionized microcluster alkaline water can make pesticide, heavy metal elements and other contaminations be better rinsed off. Dentists love alkaline water because it protects your teeth. Bacteria left on teeth generate acids, which cause cavity.
Depending on your current health condition, you may taste and feel differently after drinking Water80 ionized microcluster alkaline water for the first time: Smooth and Sweet Taste Ionized microcluster alkaline water tastes sweeter and smoother than ordinary filtered water.
If a person is dying from bowel or stomach cancer, the smell can sometimes be pungent and unpleasant. Their skin may also look pale or mottled with blue and purple patches. The person who is dying may not feel cold themselves. Users questions. Is Kangen Water worth the money? Who drinks Kangen? How long does a Kangen machine last? Can you drink Kangen water everyday?
Can I sell Kangen water?
0コメント